Fiberbuilt Grass Series Studio Golf Mat - Center Hitting - 9'X6'

Fiberbuilt Grass Series Studio Golf Mat - Center Hitting - 9'X6'

Optimize the real fairway feel of your practice sessions with Fiberbuilt’s 9’ x 6’ Center-Hitting Studio Mat. Designed for both right- and left-handed players, this mat combines ultra-durability with built-in injury prevention, creating the ultimate practice environment. Easy to assemble and engineered for maximum utility, the Studio Mat delivers unmatched performance, longevity, and realistic turf experience, making Fiberbuilt Grass the top choice for serious golfers.

• The ultimate mat systems for teaching bays or indoor studios
• Configuration accommodates down-the-line launch monitors and ball trays
• Accommodates both right- and left- handed golfers
• The hitting surface uses authentic Fiberbuilt Grass for realistic launch conditions and injury-free practice
• Assembles in just a few easy, tool-free steps
• The finished dimensions of this mat are 109"x73"x2"
• Includes: 1 Fiberbuilt Grass hitting panel, 2 Performance Turf stance mats, 1 2.635" rubber tee, 1 friction-fit real tee holder, and our exclusive tool-free modular rubber foundation with easy-lock fasteners
  

For optimum performance, you should install your golf mat on a firm and level surface like concrete, packed gravel, asphalt or a solid deck. It should not be installed on bare ground or grass.

Parts & Assembly information for the 9' x 6' Fiberbuilt Grass Series Studio Mat can be found here.

NOTE: We have temporarily discontinued production of our Adjustable Tees, and we are currently including 2.625" rubber tees and friction-fit tee holders with each new order of Fiberbuilt Grass Series mats.

Product Care

INSTALLATION RECOMMENDATIONS

OUTDOORS

It is best to install Fiberbuilt golf mats and putting greens on a firm, flat surface. Suitable locations include concrete pads, asphalt pads, wood decks or patio stones, or firm, packed crushed stone. It is best not to install on grass as the mat will kill your grass and the surface under the mat will be unstable. If you are installing on concrete it is best to ensure that there is a 2% slope to allow for adequate drainage under the mat.

INDOORS

Fiberbuilt golf mats and putting greens can be installed on indoor surfaces including concrete or carpeted floors. If installing on carpet you may notice that your mat will move slightly with the grain of the carpet while you are hitting. If this is the case, you will need to install some light duty two-way carpet tape underneath the frame of your mat to anchor it down.

PRODUCT MAINTENANCE

Regular maintenance of your Fiberbuilt® Golf Mat System will ensure maximum life for the components.

FIBERBUILT® GRASS SURFACE

Maintenance: The Fiberbuilt® Grass surface consists of 4 individual panels that can be rotated for maximum life. Below is a photo of the rotation pattern options. 

The middle panel(s) will eventually show wear, the entire hitting surface can be rotated 180o for continued use. When the middle panel(s) need replacing, remove them from the hitting surface, bring the outside panels to the centre and replace the outside panels with 2 new ones OR as shown below, when you have two hitting surfaces take the 2 end panels from the panel ‘B’ 4-pack and use them to replace the worn inner panels just removed from panel ‘A’.

To rotate the panels, remove the L-channel brackets and separate the four panels that make up the driving surface. Rotate the panels so that you have a ‘new’ panel in place of where the rubber tees would be placed. Once the panels have been rotated, to re-assemble the panel components evenly and securely us a rubber hammer and “jig” to fasten the components back in place. It is important that all four components are level to recreate the smooth hitting surface.

Once the four panels have been re-assembled you can attach the “L channel”. You will need to shift the ‘L channel” slightly, drill the self-taping Robertson #2 screws into the bottom of the panel. Do not reuse the same holes. 

Cleaning: The grass hitting surface should be pressure washed once per year to remove any sand or dirt that has accumulated in the nylon fibers.

STANCE MAT

Cleaning: The turf stance mats should be removed from the rubber foundation to be pressure washed every few months. Sand and dirt collects in the nylon fibers of the turf stance mat and will deteriorate and damage the nylon if it is not washed regularly.

Maintenance: The stance mat is square to enable you to rotate the mat to balance wear. If you have rubber stance mats, sweeping and pressure washing with water will keep them clean. Never apply any cleaning or shining agents to the stance mat.

RUBBER FOUNDATION

Maintenance: The rubber foundation should be swept out occasionally. The frame may also be pressure washed. You will need to ensure that the drainage holes do not plug up with sand and dirt. You may also consider drilling additional holes into the rubber foundation to accelerate the water drainage. To keep your rubber foundation looking clean and new, you can apply tire cleaner (like Armor All) to the outside edges only.

BALL TRAYS

Maintenance: Ball Trays should be swept and cleaned occasionally and may also be pressure washed. To keep ball trays looking new, apply a tire cleaner (like Armor All) to the ball trays.

OFF-SEASON STORAGE

Stack the hitting surface vertically against a wall and stack only 5-8 deep. Do NOT stack the hitting surface horizontally on top of each other; this will flatten the nylon fibers. The turf stance mats and the rubber foundations can be stacked on each other horizontally. Do not mix the stack.